hyt tc 365 programming software download

HYT TC 365 PROGRAMMING SOFTWARE DOWNLOAD FOR MAC
HYT TC 365 PROGRAMMING SOFTWARE DOWNLOAD MANUALS
HYT TC 365 PROGRAMMING SOFTWARE DOWNLOAD SERIAL NUMBER
HYT TC 365 PROGRAMMING SOFTWARE DOWNLOAD DRIVER

Receiver The receiver employs double conversion superheterodyne. Appendix: Initial data table Model Frequency Center IF (MHz) 1CH (C) 2CH (L) 3CH (H) 4CH (C) Range (MHz) Frequency (MHz) Rx (MHz) Tx (MHz) Rx (MHz) Tx (MHz) Rx (MHz) Tx (MHz) Rx (MHz) Tx (MHz) TC-265 (1) 136.000-150.000. 5.5 Wired Clone Mode Turn the radio on while holding down the, after two seconds, a beep sounds and red LED flashes indicating that the radio enters wired clone mode. TC-265/365 SERVICE MANUAL 5.4 PC Adjust Mode The following parameters can be adjusted through PC (only for factory adjustment): Adjustment data Maintenance record.Assignment + It’s the assignment channel during scan It’s Last Stopped the channel where scan is stopped during scan. TC-265/365 SERVICE MANUAL Priority + It’s priority channel during scan It’s the Last Stopped channel where scan is stopped during scan.Monitor Lock Squelch opens when is held down. TC-265/365 SERVICE MANUAL Function Setting: Function Function Setting (Defaults are Display Remarks Name underlined) Monitor Disable Monitor Momentary AF channel opens when is held down.Click Register Now on the bottom right corner and enter your Registration Key.

HYT TC 365 PROGRAMMING SOFTWARE DOWNLOAD DRIVER

When searching for Driver Support do not include words.

HYT TC 365 PROGRAMMING SOFTWARE DOWNLOAD SERIAL NUMBER

The channel frequency of each group is arranged as center, low, high and center frequency.ĭriver Support Serial Number Key. There are four groups and they are marked as group 0, group 1, group 2 and group 3 respectively.

HYT TC 365 PROGRAMMING SOFTWARE DOWNLOAD FOR MAC

Programming Software For Mac Arduino Programming Software Download Operation: Turn the radio on while holding down the, three beeps sound after 2 seconds and green LED flashes.

TC-265/365 SERVICE MANUAL 5.2 Manual Adjust Mode In this mode, the factory or the dealer can adjust the radio parameters in menu mode.

Connect the radio with PC You can program the radio via PC Mode through interface cable. Keyboard Entry for Mode Startup Mode Remarks User Mode Conventional Turn the radio on to enter Power on Mode conventional mode. User Mode Conventional Mode PC Mode Dealer Mode All Reset Mode Manual Adjust Mode Wired Clone Mode 2. Frame of Radio Modes Select the function from the modes and make settings according to your needs.

TC-265/365 SERVICE MANUAL Radio Modes 1.

TC-265/365 SERVICE MANUAL Indicates: Red LED glows Transmitting Red LED flashes Low battery Green LED glows Monitoring or receiving Orange LED glows Transmitting 2-Tone/5-Tone signaling Orange LED flashes 2-Tone/5-Tone standby (4) Radio On-Off/Volume Control Knob Rotate the knob clockwise to turn the radio on, rotate the knob fully counter-clockwise until a “click” is heard to turn the radio off.

Parts description: (1) Antenna (2) Channel Selector Knob Turn the selector knob to select channels 1-S (channel S can be programmed by dealer as scan function). PC mode：Set and adjust radio data with PC software or programmer in this mode. Mode User mode: Turn on the radio to enter the mode.

TC-265/365 SERVICE MANUAL Radio Overview 1.

If a damaged antenna comes into contact with your skin, a minor burn can result.

HYT TC 365 PROGRAMMING SOFTWARE DOWNLOAD MANUALS

Programming Software, Programming Cables, Service Manuals for Hyt Radios. Hyt Programming Software, free hyt programming software software downloads. Please register or login to download files from this category. HYT download service manauals and software. Do not use any portable radio that has a damaged antenna. Use only the supplied or an approved antenna. Use only HYT original batteries and chargers. Do not modify the radio for any reason.TC-265/365 SERVICE MANUAL Revision History Date Revision 2004.10 IC302 is changed from TA7368F to KIA6278F Q203/Q203 is changed from 3SK320 to 3SK318 Q102 is changed from 2SK2596 to RD01 Q105 is changed from 2SK2595 to RD07.Ĭhanges also be made on the corresponding peripheral circuits.TC-265/365 SERVICE MANUAL Contents R e v i s i o n H i s t o r y 1 G e n e r a l.

Hyt tc 365 programming software download